Online Promix SD Commissioning Form

Online Promix SD Commissioning Form
This online commissioning form is required to be filled out completely and subbmitted to WoodTech Electronics after any Promix System is commissioned for warranty and servicing proposes, fail to do so will or could void the warranty of the Promix System this is the responsibility of the installer and bowl manufacture only and not WoodTech Electronics.

Please make sure all * feilds are 100% correct and dont leave any blank.
If your not 100% sure please contact us on 0481 001 427 for any support.
Commissioning Time(Logged as QLD Time Only)

:HourMinutesAM/PM Option
Date of Commissoning

DayMonthYear
Date
Company Name for the Installment:*
Asset Owners Details
Company Contact Name*

First NameLast Name
Company Contact Phone Number*

Area CodePhone Number
Company Contact Email*
example@example.com
Installers Ref or Job Number
Job, ID or Work Number
Installer's Company Name*
Installer's Name*

First NameLast Name
Installer's Mobile*
Installer's Email*
Email Address
Additional Email 1
To be email to an additional person for viewing.
Additional Email 2
To be email to an additional person for viewing.
Additional Email 3
To be email to an additional person for viewing.
Additional Email 4
To be email to an additional person for viewing.
Promix Cab Box Ser Number:*
Label located at the Bottom of the Controller or on the Main CPU Board example-180602-6
Promix Hand Remote Ser Number:*
Label located at the rear of the Hand Remote
Vehicle Make:*
Examples: Kenworth, Mack, Hino, Isuzu etc
Vehicle Model:*
The model of the Truck like T360 (Kenworth)
Vehicle Vin No:
Vin Number
Vehicle Rego or Fleet No:*
Rego Number
What Hyd Pump Control Type is Fitted*

RexrothDanfoss
What Vehicle Transmission Type is Fitted:*

Auto TransmissionManual Transmission
10 Way Dipper Settings(Tick if On Only)

Dipper 1 - Park Brake Input (On if Required for Engine Revs)Dipper 2 - A/T Neutral Input (On if Required for Engine Revs)Dipper 3 - Engine Revs Control Type (Cruise / Linear Act is On & Analogue is Off)Dipper 4 - Proportional Hydraulics Type (Danfoss is On & Rexroth is Off)Dipper 5 - Hydraulic Pump Control (Manual / Linear Actuator is On & Electronic is Off)Dipper 6 - Plant Mix Mode(See Manual - Page 8 )Dipper 7 - Travel Calibration Mode Select(Calibration Mode On & Calibration Mode Off)Dipper 8 - ReservedDipper 9 - Danfoss Coil Current Reversal (Normal is On & Reversed is Off)Dipper 10 - Travel Mode (Pre-set is On & Programmable is Off)
Engine Revs Control Type is Fitted:*

Cruise ControlAnalogActuator
Park Brake Input:*

PositiveNegativeCANBus
Neutral Input:*

PositiveNegativeCANBus
Service Brake Input:*

PositiveNegativeCANBus
Tacho Input:*

YesNo
We Require 4 Clear Photos and Uploaded
1. Voltage Pot Postions
2. System Setup Dipper Postions
3. Analog Revs Pot and Jumper if used
4. Hyd Pump Jumpers
Please take a clear photo of the Voltage Pot Positions

Browse Files
Upload any site photos to support the Commissioning Report here Cancelof
Please take a clear photo of the 10 Way Configure Dipper Switches Positions

Browse Files

Cancelof
Please take a clear photo of the Promix SD Analog Rev’s Pot and Set Jumper Positions

Browse Files

Cancelof
Please take a clear photo of the Promix SD Hyd Pump Red jumpers Positions

Browse Files

Cancelof
Commissioning Comments .*
Please list any issues or faults while carrying out the installment , Please write Nil in the box if nothing to report
Should be Empty: