Why should I have my scope professionally mounted? Every firearm is safety checked prior to mounting the scope. The correct rings and bases are chosen for your firearm and scope combination. The base screws are torqued to 30inch lbs and secured using Loctite 242 to ensure they stay tight even on the heaviest recoiling guns. The rings are properly aligned to eliminate undue stress on the scope. The scope will be positioned so that the eye relief is correct, and the crosshairs are level. (Eye relief, eye box and crosshair position can be some what of a personal setting. We’ll allow you to shoulder the gun and set each to your taste.) The rings screws are torqued to 15inch lbs. Every scope is boresighted. Boresighting aligns the crosshairs with the bore and ensures that you’ll have enough adjustment when zeroing at the range. We finish up by wiping down your firearm with a quality gun oil so that you know it’s protected.

Boresighting is a process that aligns the bore with the reticle of the scope. It's a critical step before zeroing the rifle at the range.

Lapping, or truing up the inside surface of scope rings, can help protect the scope tube from damage and improve accuracy. Lapping can also eliminate stress on the tube, which can affect the integrity of the scope's internal moving parts.

 (includes complete disassembly, wear and or damage inspection, cleaning, lube, reassemble,  test fire, final wipe-down)

 (includes complete disassembly, wear and or damage inspection, cleaning, lube, reassemble,  test fire, final wipe-down)

Your firearm is fieldstripped, sonic cleaned, reassembled, lubricated and tested

Our average repair runs $149 and takes about 90 minutes

Includes: disassembly, concentric machining and threading, 60 degree crown, knurled thread protector, mounting device and range rod testing

Includes: disassembly, cutting, crowning, concentric machining and threading, 60 degree crown, knurled thread protector, mounting device and range rod testing

A bismuth cast of your chamber is created.  By doing so we can measure the casting to identify the cartridge and or identify issues with the chamber

Includes: creating a custom lead lap, lapping bore thru three graduating grits and before and after images of your bore

The crown is where the bore intersects with the muzzle.  If this intersection is not a perfect, concentrice exit, accuracy suffers.

The crown is where the bore intersects with the muzzle.  If this intersection is not a perfect, concentrice exit, accuracy suffers.

Drilling and tapping a hole involves creating a threaded hole in a piece of material, typically metal.

Glass bedding is a process that involves molding an epoxy-based material onto a rifle stock to fill gaps between the stock and receiver. This process is common in wood stocks, and can help fix inletting mistakes, provide a snug fit, and prevent unnecessary movements inside the stock. Glass bedding can also stabilize the barreled action within the stock, which can increase the accuracy of the rifle.

Pillar bedding is a method of bedding a rifle that involves inserting metal cylinders around the action screws to reduce compressive shifting. The pillars support the rifle's action on non-compressible "pillars" that are permanently molded into the stock. This process can increase accuracy and consistency by stabilizing the barreled action within the rifle stock. It can also reduce or eliminate stress caused by unmatched surfaces between the stock and action.

Your existing bolt handle is machined to a specific diameter and then threaded to accept the bolt knob of your choice. Bolt knob not included.

Includes rebluing

Price starting at

Includes: new bolt handle, removal of the existing bolt handle, welding on the new handle, shaping and polishing.  Two bolt handle styles available, see photos.

Priced per hour...make and model determine final charge.  Triggers and or spring kits not included

Bolt, extractor & feeding work additional

Laser engraved to ATF standards

Parts additional

Using the Timney trigger fix kit, your trigger weight and trigger feel are greatly improved.  Price includes the Timney kit.

Includes CNC inletting and coating the fresh cut with Duracoat matching color and DBM bottom metal.  Available in standard short or long action.  Magazines are additional.

Includes milling and extractor, extractor pin and extractor spring

Priced per hour...make and model determine final charge.  Triggers and or spring kits not included

Includes: populating all parts into lower and lubricating

Includes: assembling upper receiver, torquing barrel, installing handguard, dust cover, forward assist, etc.

Includes: disassembly, concentric machining and threading, 60 degree crown, knurled thread protector, mounting device and range rod testing

Includes: disassembly, cutting, crowning, concentric machining and threading, 60 degree crown, knurled thread protector, mounting device and range rod testing

Leaving weld visible

Includes: creating a custom lead lap, lapping bore thru three graduating grits and before and after images of your bore

Gas block additional

Handguard additional

Mag release additional

Free with purchase of B.A.D. lever

Includes: indicating top dead center in the mill.  Dippling and gas block install.

Includes: Indexing in mill, drilling and installing the A2 front sight

Drilling and tapping a hole involves creating a threaded hole in a piece of material, typically metal.

Priced per hour...make and model determine final charge.  Triggers and or spring kits not included

Using the Timney trigger fix kit, your trigger weight and trigger feel are greatly improved.  Price includes the Timney kit.

New bead addional

Single barrels only, choke tubes of your choice are additional

Cantilever mount and bluing or single color Cerakote included.  Available for 12 & 20ga only

Includes Remington sights and matte bluing or single color Cerakote.

Parts additional.

Parts additional.

Includes rebluing or single color Cerakote.  New action spring tube not included

Includes rebluing or single color Cerakote, new magazine tube and barrel support are not included

Includes chamber and ejector work. New ejector spring additional.

(Parts additional)

Includes fitting the rivets as flush as possible and then cold bluing them. Parts additional.

Includes fitting the rivets  flush and rebluing the receiver to factory finish. Parts additional.

Eliminates barrel movement

Includes labor and Timney Sear & Spring Kit

Weld and fit locking lug to tighten Browning OU.

Fit forend latch for easier assembly/disassembly

Drilling and tapping a hole involves creating a threaded hole in a piece of material, typically metal.

Several crown styles available (see photos) True Flush 11 degree True flush "Pro Chamfer" True flush "Recessed Capture" Dead Flat

Polish & smooth action, parts not included

Pricing starts at...

Simply dropping a trigger in is not enough, custom tuning and polishing will pay large dividends.  Trigger addional

Sight additional

Sights additional

Magazine release additional

Includes bluing or Cerakote finish

You dream it, we make it happen.  Includes rebluing or single color Cerakote

Convert Sig P320 to manual safety using Sig OEM safety kit.  Includes safety kit and installation

Drilling and tapping a hole involves creating a threaded hole in a piece of material, typically metal.

Barrel must be removed from the frame

Polish and smooth action, spring kits and parts additional

Remove old barrel, install new barrel

Includes bluing if needed

Icludes: comprehensive data capture, digital fingerprints, passport photo, eform 4 completion, cheif lawenforcement notification and 4473.

Icludes: eform 4 completion, cheif lawenforcement notification and 4473

Icludes: comprehensive data capture, digital fingerprints, passport photo, trust creation, notary, legal witness, eform 4 completion, cheif lawenforcement notification and 4473.

Icludes: comprehensive data capture, digital fingerprints, passport photo, eform 1 completion, cheif lawenforcement notification and 4473.

Icludes: eform 1 completion, cheif lawenforcement notification and 4473

Icludes: comprehensive data capture, digital fingerprints, passport photo, trust creation, notary, legal witness, eform 1 completion, cheif lawenforcement notification and 4473.

NFA transfer fee applies to each suppressor or SBR transferred to America's Gunsmith Shop

The ATF requires that short barreled rifles and short barreled shotguns be marked in a specific way. The firearm must include trust name or name and city and state. These markings must be .003" deep and no smaller than 1/16" in height and be placed in a visible area.  These markings can only be completed following your form 1 approval.

Standard pattern

Includes parts & labor

Includes bluing or single color Cerakote finish

Tons of options Call for price

Includes bluing or Cerakote finish

You dream it, we make it happen.  Includes rebluing or single color Cerakote

Magazine release additional

Convert Sig P320 to manual safety using Sig OEM safety kit.  Includes safety kit and installation

Convert Sig P336 to manual safety using Sig OEM safety kit. Includes safety kit and installation

Price includes short stroke flat trigger, spring kit and installation

Includes extended magazine release and installation

Includes extended magazine release and installation

Includes sights and installation

Includes the threaded barrel and the installation

P365 Titanium Striker Assembly - CNC Striker Housing w/ Slide Cap and installation

Includes the compensator and installation.  Requires a threaded barrel.

Perfect one-to-one, ultra smooth slide to frame fit

Non-ramped barrel

Ramped barrel

Price is starting at

Does not include cost of bushing

Bluing additional

Available in 20, 25, or 39 lines per inch

Refinishing additional , 50 LPI

Trigger additional

Hammer additional

includes: milling serrations, bluing or single color Cerakote

Rear of ejector is cold blued after fitting

Safety additional

Drilling and tapping a hole involves creating a threaded hole in a piece of material, typically metal.

Includes bluing or Cerakote finish

You dream it, we make it happen.  Includes rebluing or single color Cerakote

Polish & smooth action, parts not included

Includes rebluing the slide

Sight additional

Sight additional

Price starting at

We offer cuts that are compatible with Trijicon, Vortex, Holo Sun, Leupold, Burris, TruGlo and more. Service includes: Milling, Drilling & Taping, Cerakote the cut and Mounting & Boresighting.

For co-witness with a pistol mounted red dot or use with a suppressor Call for price

includes: Squaring bolt face and receiver, lapping locking lugs, threading, chambering, standard throating, crowning, headspacing, laser engrave the caliber into the barrel and finishing to match the receiver. We use the following barrel manufacturers: Krieger, Criterion, Brux, Proof, Shaw

Upcharge for single shots like Ruger No.1 and for Win 70 pre 64, Springfield & Enfield's, (Extractor cut)

Average price

Average cost $279

Laser engraved to ATF standards

Hourly rate

The old rifling is removed, a new redman barrel liner installed, chambered, crowned and tested.  Barrel liner additional

The old rifling is removed a .17 cal Redman barrel liner installed, chambered, crowned and tested.  Barrel liner additional

The original rifling is removed, a Redman .17 cal barrel liner installed, chambered, crowned and tested.  Barrel liner additional

Single barrels only, choke tubes of your choice are additional

And additional charge for the installation of a front sight base is required. Parts are not included.

Includes: five flush stainless chokes of your choice and a wrench for lead or bismuth. Shipping both ways is an addional $50

Includes: five extended stainless chokes of your choice and a wrench for lead or bismuth. Shipping both ways is an addional $50

Includes: five flush titanium chokes of your choice and a wrench that are steel shot safe. Shipping both ways is an addional $50

Includes: five extended titanium chokes of your choice and a wrench that are steel and tungsten shot safe. Shipping both ways is an addional $50

Includes five flush stainless chokes and a wrench for lead or bismuth shot. Shipping both ways is an addional $50

Priced per hour.  Avg is $600ish "The quality of a fine rifle or shotgun is often judged by the checkering. In addition to the functional aspect of providing a firm, non-slip grip of the stock, custom checkering adds to its appearance and value. Care is taken so that the checkering blends with the stock to complement and enhance the overall aesthetic character of the firearm, while allowing the owner a personal statement in its design. All checkering will have sharp, pointed diamonds with no overruns, and be done without borders unless specified. The checkering can be done from 18 to 32 lines per inch, with 24 LP.I. recommended for rifles, slightly finer for shotguns and accent panels

Priced per hour, Avg job takes 5 hours Our shop offers several professional wood finishes, from hand rubbed oil to high gloss lacquer. Please contact us so we can help you choose the correct finish for your firearm. Prices include: Stripping of standard finishes, sanding, removal of small dents and nicks, taping off the checkering, finishing, recutting the boarders around the checkering and resealing the checkering.

The following are assessed at a rate of $139 per hour. *Oil soaked stocks *Removal of large dents *Crack repair  *Stripping epoxy finished like on the Weatherby MkV and some Browning models *Staining if needed * Checkering repair / recut

Includes: adjustable comb and length of pull Gracoil system, all hardware, labor and shotgun fitting session as outlined below

An adjustable comb allows for proper eye alignmet over the rib. (includes Graco hardware, labor and a shotgun fitting session to ensure your eye falls directly over the rib)

The standard Graco adjustable buttplate offers three-way adjustment for perfect gun fit, higher scores and improved shooting comfort. Drop, and rotation are easily set to any position. (Includes: shotgun fitting session, length of pull is set, stock cutting and squaring, Graco hardware Kick-Eez pad and labor)

The “length of pull” will adjust in or out 1 1/8 inches and the pad plate will move up or down 1 1/2 inches, and can rotate to any comfortable position “toe in” or “toe out”. A positive locking system will hold the adjustments in place without slipping. (Shotgun fitting session, length of pull adjustment, stock cutting and squaring, Graco hardware Kick-Eez pad and labor are all included)

The GraCoil is a compression butt plate with an adjustable tension setting and adjustable pad plate. Adjustments for, drop, and rotation allow factory stocks to fit any shooter’s style. Tension will adjust from 14lbs to 70lbs with a maximum stroke of 5/16" which produces a hardly detectable response time, with no distractions between shots. Moving parts slide on Teflon® liners for a smooth and trouble free motion. It uses very little lubrication, and no maintenance is required. (Shotgun fitting session, length of pull adjustment, stock cutting and squaring, Graco hardware Kick-Eez pad and labor are all included)

The “length of pull” will adjust in or out 1 1/8" and the pad plate will move up or down 1 1/2", and can rotate to any comfortable position “toe in” or “toe out”. Tension will adjust from 14lbs to 70lbs with a maximum stroke of 5/16" which produces a hardly detectable response time, with no distractions between shots. Moving parts slide on Teflon® liners for a smooth and trouble free motion. It uses very little lubrication, and no maintenance is required. (Shotgun fitting session, length of pull adjustment, stock cutting and squaring, Graco hardware Kick-Eez pad and labor are all included)

includes: installation, buttplate, and stock cutting if needed

includes: determining your length of pull, shortening and squaring, pad installation and recoil pad. We carry and recommend Kick-Eez pads

Includes: brake, threading barrel, tapering the brake to match your barrel contour, drilling and reaming the brake for your caliber and finishing the brake to match your rifle's finish

includes: the brake, cutting barrel, recrowning, threading, tappering the brake to your barrel diameter and finishing the brake to match your rifle

Custom machined to match your barrel diameter, finish and caliber.

Our Gunsmiths can also custom fit your brake by polishing the barreled action and brake together and then refinsihing, includes bluing or single color Cerakote

The Standard Pro-Port procedure consists of "cutting" eleven compound ellipsoidal ports into each side of a barrel. These (similar to an oval) ports are placed behind the choke tube or constricted area in a series of two rows with six on the top and five on the bottom. Roundtrip shipping to Mag-na-port is $49 additional

The Standard Pro-Port procedure consists of "cutting" eleven compound ellipsoidal ports into each side of each barrel. These (similar to an oval) ports are placed behind the choke tube or constricted area in a series of two rows with six on the top and five on the bottom. Roundtrip shipping to Mag-na-port is $49 additional

Our Pigeon Port design is an enhancement to the porting design consisting of five additional ports extending back from the top row of the Pro-Port pattern. This style of porting is recommended for shooters using 2 3/4 dram equivalent or higher loads. It provides up to an additional 5% reduction in recoil and is great for use with pressure first shot, doubles, and in flyer tournaments. The extra pigeon porting is not recommended for gas or recoil operated guns and is not available on barrels under 24 inches. Per barrel when added to a standard porting job. Roundtrip shipping to Mag-na-port is $49 additional

Competitive riflemen and hunters know the importance of a fast, accurate second shot. Mag-na-port offers shooters an average of 30% reduction in recoil (actual reduction varies depending on caliber) Roundtrip shipping to Mag-na-port is $49 additional

Traditional Mag-na-porting of a handgun consists of two trapezoidal ports cut into the barrel approximately 1/2 inch from the muzzle. For the shooter this translates into a reduction of perceived recoil of 15 to 20%! Roundtrip shipping to Mag-na-port is $49 additional

Dual Trapezoidal Mag-na-porting is done on barrels over 3". This style of porting provides greater relief from muzzle lift. Using two trapezoidal ports on each side of the barrel, the primary focus of gas dissipation helps reduce the muzzle lift.  Roundtrip shipping to Mag-na-port is $49 additional

Mag-na-port offers a unique system of porting semi-automatics by using a trapezoidal port through the barrel and an oversized expansion vent through the slide to allow maximum dissipation without fouling. This process offers an alternative to shooters not wanting additonal weight or length from add on compensators.  Your gun will be far more managable and with far less muzzle lift. Roundtrip shipping to Mag-na-port is $49 additional

In-stock patterns, special order patterns additional

Bolt and trigger guard not included

At owners risk

Per set

Priced per each

Shotgun bolts and trigger guards can be coated but will not be covered under warranty

Firearms with these coatings require additional stripping 

Tons of patterns available at watertransferprinting.com

Depending on condition, not all firearms can be restored to the original finish.

Single Color

Single Color

Receiver, barrel and misc parts, mag cap, action bar etc.

Receiver, barrel and misc parts, forend iron, etc.

Single color Cerakote most AR handguards

Priced per each

Single color Cerakote most AR buffer tubes

Includes: masking off critical parts, turret, power ring, etc. and cerakote

Price per each

An up-charge of $39 will be assessed for each color. Pattern stenciling, art work and stencil cutting is an additional $69

Firearms that are e.xcessively dirty or rusty must be cleaned and an up-charge at a rate of $119/hour will be added. Depending on condition, not all firearms can be restored to the original finish.

Single color Cerakote most AR barrels

Your firearm is completely disassembled, cleaned, bead blasted, blued, reassembled, lubricated and test fired. (Polishing or removal of pitting is not included)

Your firearm is completely disassembled, cleaned, bead blasted, blued, reassembled, lubricated and test fired. (Polishing or removal of pitting is not included)

Your firearm is completely disassembled, cleaned, polished to 350 then blued (blasted and wire wheeled for satin), reassembled, lubricated and test fired. (These prices include the removal of minor pitting. Note: deep pitting cannot always be removed. Depending on condition, not all firearms can be restored to original condition.

Your firearm is completely disassembled, cleaned, polished to 350 then blued (blasted and wire wheeled for satin), reassembled, lubricated and test fired. (These prices include the removal of minor pitting. Note: deep pitting cannot always be removed. Depending on condition, not all firearms can be restored to original condition.

Your firearm is completely disassembled, cleaned, polished to a high gloss Weatherby style finish, blued, reassembled, lubricated and test fired. (These prices include the removal of deep pitting. Note: deep pitting cannot always be removed. Depending on condition, not all firearms can be restored to original condition)

Your firearm is completely disassembled, cleaned, polished to a high gloss Weatherby style finish, blued, reassembled, lubricated and test fired. (These prices include the removal of deep pitting. Note: deep pitting cannot always be removed. Depending on condition, not all firearms can be restored to original condition)

Over / Under and Side by Side barrels that are soft soldered. Note: Firearms with excessive pitting will require additional polishing. ($139hr). Firearms that are excessively dirty or rust must be cleaned and an up-charge at a rate of $139/hour will be added. Depending on the condition, not all firearms an be restored to the original finish.

Your firearm is completely disassembled, cleaned, bead blasted, parkerized, reassembled, lubricated and test fired (These prices include the removal of minor pitting. Note: deep pitting cannot always be removed. Depending on condition, not all firearms can be restored to original finish).

Firearms Engraving, you dream it, we make it a reality. Most jobs start at $69...Call for estimate.

Laser engraved to ATF standards

The ATF requires that short barreled rifles and short barreled shotguns be marked in a specific way. The firearm must include trust name or name and city and state. These markings must be .003" deep and no smaller than 1/16" in height and be placed in a visible area.  These markings can only be completed following your form 1 approval.