Omni Valve - Actuated Valve Quotation Form

The following checklist items 1-8 will verify if the EX or EXE control system package is correct for your application.

1. System requires an external hydraulic fluid supply.

YesNo

2. Hydraulic reservoir and entire pressure circuit is a closed loop (self-contained).

YesNo

3. System uses an electric motor to power a pump that supplies hydraulic pressure to the actuator.

YesNo

4. System operates by electric signal input and allows remote control.

YesNo

5. When power is supplied to the system, it will open the safety valve.

YesNo

6. As long as power is maintained to the system, valve will remain open. Upon loss of power, valve will close.

YesNo

7. ESD events (valve open/close events) can be determined by PLC or other system.

YesNo

8. Valve can be brought back in service manually. For (local control) upgrade to EXE-M, select Yes ->

YesNo

Name*

Email*

Phone Number*

Quantity needed*

API material class*

Please indicate if the Model EXE-M (Manual Pump Module) Addition is required.

Please indicate if the Pilot Module Addition is required. Example below.

See Pilot Module >>

Please indicate if the Position Indicator Module Addition is required. Example below.

See Pilot Module >>

EXE Technical Details

Orientation of the valve as mounted in service.

See Orientation Diagram >>

Confirm availability of 24 vDC power at site where system will be installed.

System Hazardous Area Certification (CL1, DIV2, UL/CSA) Acceptable..?

If No, Please indicate required hazardous area certification:

Electric Motor Amperage Draw / Run Times
The example below are based on the following model, size & pressure:

Bore	Pressure	Actuator
2-1/16"	10,000 psi	HX-30

Acceptable amperage draw of the electric motor during operation should be considered. If amerage draw using one of the standard configurations shown below is not acceptable, the system can be configured to reduce the amerage draw by changing the hydraulic pump displacement.

In some cases, achieving an acceptable average draw may require a change in actuator size. In all cases, the combination of pump displacement and actuator size impacts the time required to open the valve.

Actuator Model	Pump Disp	Max AMP Draw During Open *	AMP Draw During Cycle Time Balance	Total Opening Run Time
HX-30	1.2 cc	36	9	32 seconds
HX-30	0.8 cc	22	5.5	49 seconds
HX-30	0.63 cc	18	4.5	62 seconds

* Maximum AMP draw by the electric motor is only experienced for approximately 5% of total opening run time. For the balance of opening run time, the amp draw of the electric motor is approximately 25% of maximum.

Max. AMP Draw During Open

If amperage draw and run times above are not acceptable, please check this box and Omni will provide additional options.

Need Options

AMP options needed

Pilot Module - Single or Two Pilot System?

SingleTwo-Pilot

See Pilot Module Diagram >>

Single Pilot System - Pilot Range and Set Point:

Two Pilot System - Pilot 1 (High) Range and Set Point (PSH):

Two Pilot System - Pilot 2 (Low) Range and Set Point (PSL):

Two Pilot System - Do you require a Pilot 2 (Low Pressure) override to bring the system on-line?

If yes, a manually operated (momentary) bypass switch is required to disengage Pilot 2 while system is being energized. Please select appropriate option for location of the momentary bypass switch:

Position Indicator Module - Monitor Open, Closed, or Both Positions?

OpenCloseBoth

See Position Indicator Diagram >>

Do you want the position feedback signal wired to the electric motor junction box so feedback signal from position switches is sent to same system controlling the motor?

If yes, should cables connecting the position indicators be hard-wired or quick disconnect?

StandardQuick Disconnect

If no, and position switch feedback signal will be connected to a separate system, indicate required length of the lead wires:

18"36"72"Other

Accessories

Other Requirements? Please Specify

* After clicking submit you will receive an email with your requested details.

Tracking #

Additional Information:

Company Name

Description

PN#

Price

Delivery

Delivery instructions

Quote valid

Rev.

Payment terms