Hoist Inspection Checklist

Hoist Inspection Checklist
NOTE:

It is intended that the equipment be checked daily and weekly by the operator. Any defect must be reported underthe space left for remarks. The superintendent will in turn notify the project manager and/or equipment department,who will see to it that the defect is remedied. This weekly check does not relieve the operator of the responsibility toimmediately report to the superintendent any fault. This weekly report is to be retained in the Daily Check List Book.
HOIST INSPECTION CHECKLIST
Project Name*
For Week Commencing*

MonthDayYear
Date
Name*
Equipment Number*

DAILY CHECK*

Rows	M	T	W	TH	F	S	s
1. Check for oil leakage, and refill oil if necessary.
2. Check the oil level of the hydraulic tank.
3. Check the brakes. See Operating Instructions in the cage. See separate instruction for checking brake torque
4. Check the gate and trap door interlockings, the three-phase switch and the equalizer switch. (Try to run the hoist leaving the door open, then leaving the trap door open, then with the three-phase switch turned off, and finally with the equalizer switch turned off. The hoist must not start, but remember to check only one function at a time
5. Check all door interlocking.
6. Check that cage and counterweight travel areas are free from obstruction.
7. Grease cage rollers.
8.Validate that the daily hoist routine inspection is carried out according to the instruction sign in the cage.

Remarks: Investigate unusual noises or problems; record corrective actions
Operators Signature*

Clear
Superintendents Signature*

Clear
If completing only daily, click "SUBMIT" to complete form. If competing weekly, monthly, 6 months, annual checklist, select appropriate form below.
- 1. Check that the roller assemblies and counter rollers of the machinery plates are tightened.
  
  MonthDayYear
  Date
- 2. Check the tensioning of the V-belts
  
  MonthDayYear
  Date
- 3. Check the position of limit and three-phase cams and make sure they work correctly.
  
  MonthDayYear
  Date
- 4. Check the cable guides and all plate springs.
  
  MonthDayYear
  Date
- 5. Check the position of the cable support arm in relation to the cable guides.
  
  MonthDayYear
  Date
- 6. Check the attachment of the mast tie-ins.
  
  MonthDayYear
  Date
- 7. Tighten all mast bolts. Tightening moment 350 Nm (258 lbf x ft.).
  
  MonthDayYear
  Date
- 8. Check the adjustment and attachment of the counterweight guide rollers.
  
  MonthDayYear
  Date
- 9. Clean the cooling flanges of the electric motor.
  
  MonthDayYear
  Date
- 10. Check that the power cables are undamaged.
  
  MonthDayYear
  Date
- 11. Check wire rope, cable clip connections, and counterweight.
  
  MonthDayYear
  Date
- 12. Check electrical contacts.
  
  MonthDayYear
  Date
- Remarks: Investigate unusual noises or problems; record corrective actions
- Operators Signature
  
  Clear
- Superintendents Signature
  
  Clear
- 1. Check mast for cracks.
  
  MonthDayYear
  Date
- 2. Check torque of anchor bolts.
  
  MonthDayYear
  Date
- 3. Check hoist mast for plumb.
  
  MonthDayYear
  Date
- 4. Check the wear of the pinions and the rack.
  
  MonthDayYear
  Date
- 5. Check the wear of the worn gear through the inspection plug.
  
  MonthDayYear
  Date
- 6. Lubricate according to the Lubrication Diagram.
  
  MonthDayYear
  Date
- Remarks: Investigate unusual noises or problems; record corrective actions
- Operators Signature
  
  Clear
- Superintendents Signature
  
  Clear
- 1. Check the play of the ball bearings and the wear of the cage and counterweight rollers. If the rollers are worn, adjust according to illustration. If the bearings are worn, change the guide rollers.
  
  MonthDayYear
  Date
- 2. Check the safety device by carrying out a drop test (see “Drop Test”). For hoists with counterweight heavier than the dead weight of the hoist cage, check that machinery and safety device plates are close together, without play, when the counterweight is unloaded. If necessary, use the eccentrics under the safety device plates for adjustment. See manual forinstructions.
  
  MonthDayYear
  Date
- Remarks: Investigate unusual noises or problems; record corrective actions
- PCL Construction Resources Inc. Signature
  
  Clear
- Superintendents Signature
  
  Clear
- 1. Check the coupling between the electric and the worm gear.
  
  MonthDayYear
  Date
- 2. Check the ball bearings of the top pulley. Change the bearings if necessary.
  
  MonthDayYear
  Date
- 3. Change filter first time after 50 hours and thereafter every 500 hours. Always clean strainer at this time.
  
  MonthDayYear
  Date
- 4. Change oil after 2,500 hours. See manual for proper service.
  
  MonthDayYear
  Date
- Remarks: Investigate unusual noises or problems; record corrective actions
- PCL Construction Resources Inc. Signature
  
  Clear
- Superintendents Signature
  
  Clear
- What is your email?*
  example@example.com (A copy of the final permit will be sent here.)
- Should be Empty:

Hoist Inspection Checklist

HOIST INSPECTION CHECKLIST

If completing only daily, click "SUBMIT" to complete form. If competing weekly, monthly, 6 months, annual checklist, select appropriate form below.