TY-300 Pre-Installation Site Survey

TY-300 Pre-Installation Site Survey

The site survey must be completed before Roland DGA ships the Roland TrueVIS printer. The information in this survey will ensure that you are prepared to receive the machine shipment and have a smooth installation experience. Failure to prepare for the printer's arrival via the freight company will result in additional freight charges.

Delivery does not include removal from the delivery truck. A forklift may be needed. We have lift gates, but they are not always an option. Failure to prepare facilities and electrical needs before the arrival of installation personnel will result in additional installation charges.

The customer is responsible for uncrating, moving the printer and shaker into position, and is responsible for setting up the electrical requirements.

Business Name

Address

Street Address

Street Address Line 2

CityState / Province

Postal / Zip Code

Name

First NameLast Name

Phone Number

Please enter a valid phone number.Format: (000) 000-0000.

Email (Completed survey will be sent here)

example@example.com

Is the person listed above the contact for installation and training?

Name of installation contact

First NameLast Name

Phone Number

Please enter a valid phone number.Format: (000) 000-0000.

Email

example@example.com

Select Model and Ink Configuration

TY-300

Roland TY-300 Direct-to-Film Commercial Printer/Cutter

Free Ink Configuration

TY-300 DTF Printer Specifications

Working Environment for the Machine

Roland devices operate optimally within a specific range of temperature and humidity. Failure to operate in this range can result in poor print quality or uncured ink.

During operation: Temperature: 68 to 82 °F (20 to 28 °C), humidity: 40 to 60% RH (no condensation)
During non-operation: Temperature: 41 to 104 °F (5 to 40 °C), humidity: 20 to 80% RH (no condensation)

Note: It is important to note that these requirements apply to all DTF solutions available on the market and are inherent to pigment-based printing technology.

Ensure that the room where you are using the machine is well-ventilated. (Recommended ventilation capacity: 2,500 m3/hour) Be sure to install a ventilator when installing the machine in a sealed room or a room with poor ventilation.

Do not place the machine in an area where it will be exposed to corrosive gases.

Place the main machine on a strong and level base. Inclination on any side should be no more than 5 mm (0.2”).

Do not place the machine where it may be subjected to strong vibrations.

Avoid areas exposed to sudden temperature changes.

Areas directly exposed to cool air from an air conditioner.

Areas directly exposed to heat from a heater.

Electrical Requirements for the TY-300

The Roland TY-300 can plug into a normal wall outlet. The power requirements are below:
• TY-300 100-120 / 220-240 Vac 50/60 Hz 6.4/3.0 A
Although it is not needed, Roland DGA highly recommends using a battery backup or surge protector that can manage the power requirements.

Electrical Requirements for the RDTF-S800 Shaker

AC 200-240v @ 50/60 Hz
Current 16A x 1 – (Single Phase)
(Plug and Wall Receptacle are NOT included)

Wall Receptacle: 20 Amp 250-Volt NEMA 6-20R 2-Pole Commercial Grade Single Straight Blade Receptacle

PLUG: 20 Amp 250-Volt NEMA 6-20P Straight Blade Plug

VersaWorks 7 Software and Computer Requirements

I have reviewed the specifications for my device and acknowledge the electrical, environment, and working area to be within specifications.

It is the customer's responsibility to note any shipping damage when the machine arrives. Please note damage on the receiving documents and provide Roland with pictures of the damage.

Does the delivery site have access to a forklift and pallet jack?

If No, what arrangements are being made to receive the machine?

Will you have a forklift available or at least 4 people to assist with lifting the printer onto the stand?

Have print samples been requested and approved?

List the common types of material that will be used.

Request a Roland representative to contact you for more information on the following:

Additional notes

Name

First NameLast Name

Signature acknowledging installation site survey being complete

Select Model and Ink Configuration*

Working Area Requirements

Select Model and Ink Configuration