2.1 PROFESSIONAL COURTESY
The on-going reputation of the EPH Group depends very much on the way you drive your vehicle and courtesy that you extend to the clients and the community. The road is there to share and therefore, it is a company requirement that you display courtesy and restraint towards other road users and general members of the public.
- Completing a Daily Pre-Vehicle Check
- Fit for duty
- Observing speed limits & seat belt laws
- Observing fatigue regulations
- Not being under the influence of drugs or alcohol
- Not tailgating other vehicles
- Applying reliable and effective load restraint practices
- Being considerate of other road users Not using noisy engine brakes at inappropriate times and places
- Obeying all other laws
2.2 SPEED RESTRICTION
As a professional and competent driver, you must always adjust your driving to the existing conditions. Never exceed the posted speed limit and drive to the road and environmental conditions.
You should always apply the following rules:
2.2.1 Always reduce your speed in wet conditions.
2.2.2 Drive cautiously in fog or heavy rain.
2.2.3 Descend hills use lowest gear to suit the conditions.
2.2.4 Always observe the special limits that apply for road works etc.
DO NOT exceed the posted maximum speed
2.3 FATIGUE MANAGEMENT
Standard hours work and rest time
Independent Contractors operate under the standard hours work and rest option. Under standard hours, drivers must not work for more than 12 hours in any 24-hour period. Work includes the following tasks related to the heavy vehicle:
- Loading and unloading the vehicle.
- While in queues, in the driver’s seat, waiting to load/unload.
- Inspecting, servicing, or repairing the vehicle. Inspecting or attending to the load on the vehicle.
- Cleaning or refuelling the vehicle.
- Recording information.
- Work and rest time must be taken in accordance with the following table.
SOLO DRIVERS
| TIME: |
WORK: |
REST: |
| In any period off... |
A driver must not work for more than a maximum of... |
Must have the rest of that period off work with at least a minimum break off... |
| 5 1/2 hours |
5 1/4 hours work time |
15 continuous minutes of rest time |
| 8 hours |
7 1/2 hours work time |
30 minutes rest time in blocks of 15 continuous minutes |
| 11 hours |
10 hours work time |
60 minutes rest time in blocks of 15 continuous minutes |
| 24 hours |
12 hours work time |
7 continuous hours stationary rest time* |
| 7 days |
72 hours work time |
24 continuous hours stationary rest time |
| 14 days |
144 hours work time |
2 x night rest breaks** and night rest breaks taken on consecutive day |
*Night rest breaks are 7 continuous hours stationary rest time taken between the hours of 10pm on a day and 8am on the next day (using the time zone on the base of the driver) or a 24 continuous hours stationary rest break.
**Stationary rest time is the time a driver spends out of a heavy vehicle or in an approved sleeper berth of a stationary heavy vehicle.
Want to know more? Head to this link: https://www.nhvr.gov.au/safety-accreditation-compliance/fatigue-management/work-and-rest-requirements-standard
2.4 MASS, DIMENSION, LOADING
- The weight and dimensions of loads on heavy vehicles.
- Warning signs and permit requirements for over mass/over dimensional loads.
- How loads must be restrained to meet the performance standards of the National Regulations; and…
- Roads on which certain classes of heavy vehicles can travel to manage risks of excessively large vehicles on road infrastructure or to the public amenity.
The weight (mass), dimension and way that a vehicle is loaded have a direct impact on the safety of heavy vehicles on our roads. Overweight, uneven loads, loads that exceed the dimensions of the vehicle or loads that are not securely restrained the risks to the transport task including:
- Vehicle instability.
- Increased wear and tear on the vehicle and its components (tyres, brakes, steering).
- Wear and tear on the road infrastructure.
- The driver having less control of the vehicle than expected which can contribute to an accident.
- Loads that are not adequately restrained can cause spillage and create hazards for other road users including being struck by debris, uneven road surfaces affecting stopping distances and vehicle control.
- Scale calibrations should be carried out every 3-6 months.
2.5 LOAD RESTRAINT
Loads must be restrained to prevent any spillage or leakage and to prevent materials and their particles ejecting from the trailer in transit. EPH requires that Independent Contractors vehicles have an automated or mechanical tarping system that can be operated via a remote control from within the truck cabin, eliminating the need to drivers to exit the vehicle.
2.6 DEFENSIVE DRIVING
You should always drive in a manner that will help you to avoid an accident, despite incorrect/inappropriate actions of others or poor driving conditions. Defensive driving requires a high degree of anticipation. Some helpful techniques, safe following distances, do not tailgate, driving under the speed limit.
2.7 VEHICLE BRAKING
One of the most important single skills that a professional and competent driver possesses is bringing a loaded vehicle to a controlled stop in city and open road conditions.
You may need to brake heavily but you must also be aware of the possible consequences.
As a guide, you should always be aware of traffic conditions in front of you. In doing so, you are adjusting your own driving conditions to avoid the need for heavy braking.
Always brake with care, remembering that the truck will react differently according to the weight of the load, weight distribution of the load and road surface condition.
You should never, under any conditions, drive a vehicle with faulty or suspect brakes. You must always as the vehicle owner assess the fault and remedy any repairs immediately. You must not conduct business with the EPH Group and provide a vehicle that does not meet roadworthy requirements or not fitted with the appropriate safety requirements.
Engine brakes are auxiliary to the main service brakes. In general, the following should be observed regarding engine brakes:
- DO NOT use the engine brake on slippery or wet surfaces, as a jack-knife may occur.
- DO NOT use engine brakes in or near residences and built-up areas, as this causes excessive noise and is a public disturbance
2.8 TAILGATING
By law you are required to maintain a gap between yourself and the vehicle directly in front of you, so that heavy braking will not be required. The gap is based on several factors including speed, vehicle weight, traffic congestion and road condition. During wet weather or other adverse conditions, the gap distance should be doubled.
Always remember, appropriate gap distance between other road users is a key defensive driving tool.
2.9 OVERTAKING/PASSING
You should always avoid overtaking in awkward, inappropriate situations or where there is unclear vision. Reckless and negligent driving will result in complaints that in effect will be investigated by the EPH Group Compliance Team.
In general, you should not overtake/pass in the following situations:
- Over continuous or unbroken lane separation lines.
- On narrow roads.
- Near or on a curve or crest.
- Near or on a bridge.
- Near or on a railway crossing or tunnel.
- When clear vision is restricted.
- Through road work areas.
Do not indicate or signal to encourage other road users to overtake or pass. This action is against the law and may cause you to be responsible should an incident occur.
2.10 ROAD AND WORKSITE HAZARDS
During most journeys that you take, there will be hazards on and near roadways and work sites. Always be alert for these hazards and make your adjustments as necessary.
Examples of hazards are:
- Rough/slippery surfaces.
- Narrow or winding roads/Road works.
- Overhead power lines, Low wires or awnings.
- Low bridges, tunnels etc.
- Crossings, rail/people. Traffic Control.
- Underpasses and trees.
- Excavations and trenches.
- Other Plant and Machinery
Be aware that your vehicle itself may become a road hazard when it is parked on a roadway, broken down or otherwise. In this circumstance, use portable warning triangles (example see below):