Training Video & Questionnaire
Watch the training video, then complete the questionnaire at the end.
Your Name
*
First Name
Last Name
Your Email
*
example@example.com
FIREX Installation Knowledge Check
Select the best answer to each question. Base your answers on the FIREX installation training.
You rip a factory-treated siding board to fit. What must you do to the newly exposed edge?
*
A. Apply stain only.
B. Brush on the supplied FX Lumber Guard XT, allow it to become dry to the touch, then stain before installation.
C. Install it without additional treatment.
You make an end cut to shorten a board. What does FIREX require for that cut?
A. Apply stain to the exposed end cut; additional penetrant is not required.
B. Apply penetrant only.
C. No additional protection is needed.
When should stain be applied to a ripped edge treated with FX Lumber Guard XT?
A. Immediately, while the penetrant is still wet
B. After the board has been installed.
C. When the penetrant is dry to the touch, before installation.
What is FIREX’s recommendation for exterior wood material smaller than 4×4?
A. Treat only material near windows.
B. Treat all exterior material smaller than 4×4 with penetrant, regardless of height.
C. Treat only material that will remain visible.
Exterior framing associated with glulams or outlookers needs field treatment and will soon be inaccessible. What should the installer do?
A. Coordinate with the builder and BWP so treatment occurs before access is lost.
B. Wait until the exterior installation is finished.
C. Assume concealed material does not need treatment.
How should installers understand FIREX’s fascia treatment recommendation?
A. Fascia is excluded from the FIREX package.
B. Fascia treatment replaces soffit treatment.
C. FIREX recommends treating fascia as part of the overall exterior protection package, even where code does not require it.
Type option 4
What is the main objective at window trim, soffits, and wall connections?
A. Leave openings into concealed spaces.
B. Maintain protection at connections and avoid exposed paths into concealed spaces.
C. Focus only on the appearance of the finished wood.
What should you do if you are unsure whether a component needs treatment or how to handle a field modification?
A. Contact the builder and BWP/FIREX before proceeding or covering the area.
B. Use stain as a substitute for penetrant.
C. Complete the installation and ask afterward.
Back
Next
General Installation - Best Practices
Use a baby-powder chalk line to establish a clean, straight guide for all exposed face nails or screws. Baby powder provides a visible installation line without leaving the permanent staining that traditional colored chalk can cause on finished wood. For 1x6 siding (nominal 5"), use one blind crown staple in the tongue and one face nail or screw 1' from the groove side edge. For boards over 6" wide, use two face nails or screws, positioned approximately 1 inch in from each edge of the board. Consistent spacing and straight fastener lines are part of a clean, professional FIREX installation.
Agree
FIREX material should arrive neatly stacked, protected, and covered. During installation, keep all material clean, dry, and organized. Dirt, mud, footprints, and other jobsite debris can be difficult to remove from finished wood and may negatively affect the final appearance.
Agree
Think ahead as you install. Save longer boards for tall runs and pay attention to the lengths included in your siding package. Reduce waste by planning cuts intentionally—for example, use a 12' board for two 6' pieces or an 8' board for two 4' pieces when appropriate, rather than simply using whichever board is easiest to grab. BWP does a physical takeoff, supplies length specific material, and typically plans for approximately 10–15% material waste. Poor material management can exceed that allowance, resulting in additional pickup orders, delays, and added cost to complete the siding package.
Agree
Use the BWP-supplied stain to seal all exposed end cuts during installation. Proper end sealing helps limit moisture absorption through the cut ends of the wood; leaving them unsealed can contribute to moisture wicking, warping, and eventual discoloration that may affect the appearance and performance of the finished siding.
Agree
I have watched the full FIREX installation training and understand the field-treatment and installation instructions. I agree to treat ripped edges as instructed, stain end cuts, and coordinate any necessary field treatment before materials become inaccessible. If I am unsure how to proceed, I will contact the builder and BWP/FIREX before continuing.
Agree
Signature
Any additional comments or questions?
Continue
Continue
Should be Empty: