ecoFINISH Post Visit Checklist

ecoFINISH Post Visit Checklist
EcoFINISH Representative*
Purpose of Visit*

Sales VisitTraining
Visit Start Date*

MonthDayYear
Date
Visit End Date*

MonthDayYear
Date
Distributor Company Name*
If within the US, Canada, France, or Spain, mark "N/A"
Dealer Company Name*
Names of those present*
Company Phone Number

Country CodeArea CodePhone Number
Site Address*

Street Address

Street Address Line 2

CityState/Province

Postal /Zip CodeCountry
Notes from Sales Call:
Case number
If none mark as NA
Have you discussed the need for sequestering agents? Have sequestering agents been added to the pool?*

YesNo
Did you discuss safety practices and precautions ?*

YesNo
Training Visit Checklist:

(If Sales call, skip to the bottom)
Pool Size
Coatings Colors
ie: Kona Coast, Blue Mist, Santorini
Epoxy Used
Number of Kits
Powder Used
Total Pounds
Ambient Temperature
Surface Temperature
Humidity
Acid Used During Etch
Acid Volume (etch)
How many crew members on site?
Substrate
Drain pool, remove hydrostatic plugs & repair damaged areas.
Comments:
Acid etch surface to clean and create a rough profile to that of 60-80 grit sandpaper. The surface must feel rough and exhibit open pores after fresh water rinse. Failure to roughen the surface will result in a poor mechanical bond to the surface.
Comments:
Power wash the entire surface with extreme care to remove all contaminants.
Comments:
Dry all surfaces with weed burner heat torches. This process step also provides the final test for the surface to find any areas that will delaminate and pop from the installation gun heat. Finding them now allows for their repair prior to aquaBRIGHT installation start.
Comments:
Tape & mask all tile, seal any open fittings, remove all pool lights, wrap the light cords, and protect fittings and fixtures.
Comments:
Blend one (1) full kit ("A" + "B") of X-40 Epoxy Resin and Hardener then add one (1) full gallon of Acetone for 60 seconds with an epoxy mixer.
Comments:
Completely saturate the surface with the 50/50 solution to the point of rejection. Inspect the substrate...the entire surface should show a glossy epoxy appearance. Use a long extender paint roller handle to recoat any area that appears dry. Optimal 50/50 cure time is 10-14 hours before 100% application. Never exceed 24 hrs cure time, or reapply 50/50 .
50/50 Set Time*

:HourMinutes
Epoxy Used*

X40X40EX40MCX40C
Comments:
Browse Files

Cancelof
Apply a 100% strength RED-TINTED X40 epoxy coat. Make sure to apply a thin coat to the entire surface. Note - Pool fittings are typically made from PVCs. The X40 epoxy will not adhere to these fittings. Make sure not to coat these fittings with the X40 epoxy.
100 Set Time*

:HourMinutes
Epoxy Used*

X40X40EX40MCX40C
Comments:
Apply “Hot Flock” coat. Apply into tacky epoxy moving from a side to side motion with the gun tip about 3 feet from the substrate. Begin coating the floor, and flock into the pool, then coat the walls beginning each section from the top tile line and working down to the cove. ENSURE EPOXY REMAINS “TACKY” THROUGHOUT THE “HOT FLOCK” INSTALLATION. DO NOT INSTALL ONTO HARD SET, FULLY CURED EPOXY. BOND FAILURE WILL OCCUR.
Comments:
Allow proper time for Flock Coat to cool to ambient temperature prior to installing additional coats.
Comments:
*Apply the 2nd coat by reducing the powder feed rate.
Comments:
*Apply the 3rd coat by reducing the powder feed rate.
Comments:
Photos:

Browse Files

Cancelof
Total Cost of Trip*
Please document the trip cost on the Trip Cost Spreadsheet
Have you provided the Installation Questionaire to the installers and their crews? https://forms.gle/i7qDFs3pKoKoAq516

YesNo
Type a question
Should be Empty:

ecoFINISH Post Visit Checklist

Training Visit Checklist:

Please document the trip cost on the Trip Cost Spreadsheet